FIXTURE CANOPY
CENTER STEM
KNOB
ROD
SMALL
LOOP
SOCKET
COLLAR
SHADE
SOCKET
SHADE
HOLDER
JUNCTION
BODY
FIGURE1
ASSEMBLY / INSTALLATION INSTRUCTIONS
1 Before beginning the installation, carefully unpack and identify
all parts, referring to the illustration(FIGURE1).
2 Turn power to the installation point OFF at circuit breaker
3 Thread the end of CENTER STEM onto nipple on top center
of JUNCTION BODY Hand tighten until snug Locate top ends
of RODS through holes on FIXTURE COVER and thread KNOBS
onto the top ends. Proceed to slide downwards and thread ends
of RODS into SMALL LOOPS and hand tighten until snug.
4.Thread the nipple in the bottom center of FIXTURE CANOPY into
HEX COUPLING in the center of FIXTURE COVER. Hand tighten
until snug. Proceed to thread FIXTURE LOOP onto the nipple on
the top center of FIXTURE CANOPY and tighten until snug.
5Fasten
the CROSSBAR to the OUTLET BOX with (2)OUTLET BOX
SCREWS(not supplied). Proceed to thread LOCK NUT A
and SHAKE PROOF WASHER A onto the top end of NIPPLE.
Thread NIPPLE into the center of CROSSBAR. Locate the LOCK
NUT B onto the bottom end of the NIPPLE. Tighten LOCK NUT A
against CROSSBAR with plier until snug.
6. Locate the FIXTURE CHAIN and determine desired hanging
height of fixture. Adjust chain by removing links if needed.
Please note that depending on chain material thickness, you
might be required to use chain pliers to spread links open.
Proceed to attach one end of chain to FIXTURE LOOP, attached
to top of fixture. Pass the fixture wires through FIXTURE CHAIN
alternating links. Proceed to pass the fixture wires through the
following mounting components in this order: 1)CANOPY LOCK
RING; 2)LOWER CEILING CANOPY; 3)UPPER CEILING
CANOPY; 4)CANOPY CHAIN LOOP; 5)SHAKE PROOF
WASHER B.
7. (2 people recommended for the
remaining steps) Position the fixture under the ceiling mounted
outlet box. Pass SHAKE PROOF WASHER B over the NIPPLE.
Thread CANOPY CHAIN LOOP onto NIPPLE. Thread LOCK
NUT B down the NIPPLE, against the CANOPY CHAIN LOOP and
snug with pliers. Pass the wires through the NIPPLE. Take up
wire slack and trim wires so that approx. 6” will remain inside
outlet box. Proceed to attach the top of the FIXTURE CHAIN to
the bottom of the CANOPY CHAIN LOOP. Using wire connectors
(not supplied) connect the HOUSE GROUND WIRE to the
FIXTURE GROUND WIRE connect the HOUSE WHITE WIRE
to the FIXTURE SUPPLY WIRE (WHITE or RIBBED SIDE);
connect the HOUSE BLACK (or RED) WIRE to the FIXTURE
SUPPLY WIRE(BLACK or SMOOTH SIDE). Wrap each
connection with approved electrical tape.
8. With the proper connections made, proceed to push the LOWER
CEILING CANOPY with UPPER CEILING CANOPY upward over
the OUTLET BOX. Be sure that all wires are carefully tucked into
the OUTLET BOX cavity. Secure canopies against ceiling by
threading CANOPY LOCK RING onto the CANOPY LOOP.
Tighten until snug.
9 Locate SHADE over SOCKET onto SHADE HOLDER Secure
by threading SOCKET COLLAR onto SOCKET and tighten
until snug Install bulbs referring to fixture markings and or
labels for maximum wattage
10 Restore power to the installation point ON. Retain this sheet
for future reference.
.
..
.
.
/
.
.
..
(,)
;
.
.
.
For Canadian installations please refer to Page 2
Making the connections:
IF IN DOUBT ABOUT ELECTRICAL INSTALLATION,
CONSULT A LICENSED ELECTRICIAN!
IS GE5006
Page1of3
01 06
-
.
OUTLET BOX
HOUSE SUPPLY and
GROUND WIRES
OUTLET BOX SCREWS
not supplied()
GREEN GROUND SCREW
CROSSBAR
SHAKE PROOF
WASHER A
LOCK NUT A
NIPPLE
LOCK NUT B
SHAKE PROOF
WASHER B
CANOPY CHAIN LOOP
FIXTURE SUPPLY
and GROUND WIRE
FIXTURE CHAIN
UPPER CEILING
CANOPY
CANOPY LOCK RING
FIXTURE SUPPLY
and GROUND WIRE
FIXTURE LOOP
LOWER CEILING
CANOPY
HEX COUPLING
FIXTURE COVER
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
(3 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern